PIC32CM3204JH00048T-I Datasheet: Key Parameter Quick Reference and Performance Benchmarking

During the embedded system selection process, the efficiency of consulting datasheets often determines how quickly a project can get off the ground. According to a comparative analysis of mainstream 32-bit MCU datasheets, the PIC32CM3204JH00048T-I achieves a high level of peripheral integration density and energy efficiency balance within the same package size. This article systematically reviews the key specifications, peripheral resources, and real-world performance of this model, helping you quickly locate relevant information during the selection and development phases, thereby reducing time costs associated with repeatedly flipping through datasheets.

I. Product Positioning and Core Specification Overview of the PIC32CM3204JH00048T-I

1.1 Interpretation of Model Naming Conventions and Package/Pin Configuration

You can quickly extract key information from the model string: the series identifier points to the PIC32CM series, 3204 represents a combined code for Flash capacity and pin count, the "48" in JH00048T-I corresponds to a 48-pin package, the "T" suffix indicates a thin-profile package variant, and "I" denotes an industrial-grade temperature rating. This naming convention allows you to make a preliminary assessment of differences between adjacent models without consulting the datasheet.

Under a 48-pin package, the number of available I/O pins and the distribution of multiplexed functions are primary considerations when selecting a device. You need to verify whether the required communication interfaces, analog channels, and GPIOs can all be mapped within the given pin budget. The supply voltage range and operating temperature range should also be checked after confirming the package type, to avoid rework later due to electrical mismatches.

1.2 Core Architecture and Memory Resource Allocation

PIC32CM3204JH00048T-I is based on a 32-bit core architecture, and its maximum operating frequency determines the upper limit of response for computationally intensive tasks. The capacity ratio among Flash, SRAM, and EEPROM directly affects firmware complexity and data recording capabilities; you should evaluate available storage space in conjunction with protocol stack usage and buffering requirements. Boot mode and memory mapping methods impact the feasibility of bootloader design and online upgrade solutions, so it is recommended to define their mapping logic early in the development process.

II. Quick Reference to Core Parameters in the Datasheet: Electrical Characteristics and Peripheral Resources

2.1 Quick Reference Table of Key Electrical Parameters

Absolute maximum ratings and recommended operating conditions are the first boundary information that must be locked down in the datasheet. Regarding power consumption, the typical current values for run mode, sleep mode, and standby mode together form the basis for energy efficiency evaluation; you should combine these with the duty cycle of your target application to calculate average power consumption. GPIO drive capability and input threshold levels determine the feasibility of directly driving peripheral circuits.

2.2 Overview of Peripheral Interfaces and Timer Resources

The number and maximum data rate of communication interfaces are frequently referenced entries in datasheets. The number of UART, SPI, I2C, and USB channels must align with the system topology, while the maximum data rate defines the bottleneck for data transmission. The number and resolution of timer, PWM, and counter channels together determine the upper limit of precision for motor control and timing generation. The number of ADC/DAC channels, along with their sampling rates and accuracy specifications, directly impacts the design margin of the analog signal chain, whereas the integration of comparators and operational amplifiers affects how much the peripheral bill of materials can be streamlined.

It is recommended to organize the aforementioned peripheral resources into a quick-reference table and annotate reuse conflict relationships, which can significantly reduce the likelihood of repeated pin assignment adjustments during the schematic design phase.

Overall, the PIC32CM3204JH00048T-I demonstrates comprehensive parameter integrity and consistent measured performance in its datasheet, making it a reliable choice for medium-complexity embedded designs. It is recommended that you use the core parameter quick-reference table as a starting point during the selection phase, and verify key metrics with actual test data to shorten the evaluation cycle and reduce design risks.

Key Summary

• The model number of the PIC32CM3204JH00048T-I directly indicates the Flash capacity, pin count, and temperature grade; for the 48-pin package, priority should be given to verifying the I/O multiplexing distribution.
• The typical power consumption values and GPIO drive capability listed in the datasheet are critical anchors for energy efficiency assessment, and average power consumption should be calculated based on the application's duty cycle.
• The number of communication interfaces and timer resources determines the feasibility of the system topology; it is recommended to compile a multiplexing conflict table to expedite pin assignment.
• Starting with the core parameter quick reference table, you can turn manual browsing time into design decision efficiency.

Frequently Asked Questions